The Inmood Pebble AIO kit runs on a 900mAh battery rechargeable by the USB-C port. The Inmood Pebble AIO kit employs refillable pods with a 3ml capacity. Moreover, the refillable pods use two airflow options and removable coils. Besides, The Inmood Pebble AIO kit is an easy-to-use vape device to carry around by the pocket.
The Inmood Pebble vape pod kit is a lightweight device [36g] with modest shapes of 76mm by 52mm by 19mm. The Inmood Pebble vape pod kit features two case options: plastic and metal. The top side of the mod has a pod compartment, and the bottom employs a USB-C port. In addition, the Inmood Pebble vape pod kit has no display or buttons. The case features only a single LED light indicator.
The Inmood Pebble pod mod is powered by a built-in 900mAh battery. The inhaling sensor compensates for the lack of buttons, which starts the Inmood Pebble pod mod. Furthermore, the Inmood Pebble pod mod charges by the USB-C port with a power of 5V/1.5A.
The Inmood Pebble pod kit matches the fully transparent plastic pod with a 3.0ml e-juice compartment. The bottom side of the Inmood Pebble pod kit pods holds the two connection magnets and the filling hole hidden under the silicon plug. Also, the bottom side has a spot with an exact position for coil insertion. Attention, the Inmood Pebble pod kit is incompatible with the Inmood Revolve pods.
The Pebble pod employs 0.8Ω removable mesh coils. Attention- the Pebble pods are incompatible with the Inmood Revolve coils because they are a little shorter.
The Inmood Pebble kit, like the Inmood Revolve kit, employs two pre-adjusted airflow options. The chosen option depends on which side the pod is in the batter. To change the airflow option, take the pod off the mod, change the position to 180, and push-fit back to the mod.
The Pebble by Inmood holds the LED light indicator on the lower side of the device. The LED light indicator displays the following battery levels:
The LED light stays on during vaping when the battery is between 100% and 40%;
The LED flashes two times after vaping when the battery level is between 40% and 10%;
The LED flashes four times after vaping when the battery level is lower than 10%.
During the charging, the Pebble by Inmood LED indicator displays the following battery levels:
Bellow 40%- the LED light flashes slowly;
40% and more- the LED light flashes faster;
100%- the LED light stays on.
Inmood Pebble AIO Pod Starter Kit Features:
Model: Inmood Pebble AIO pod starter kit
Product Type: AIO
Power: Built-In 900mAh
Variable Voltage: No
Pod Capacity: 3ML e-juice
Replaceable Pod: Yes
Pod Installation: Magnetic
Coils Installation: Push-Fit
0.8Ω Mesh Coil
E-Juice Compatibility: Nic Salt/ Freebase
Case Material: Plastic or Metal
Charge AC/USB: 5V/1.5A
1x Pebble Mod
1х Pebble Pod
2х Pebble Mesh Coil 0.8Ω
1х USB-C Cable
The coils employ organic cotton filler. Therefore, it is necessary to soak it in e-juice to prevent cotton from burning out. To do this, you need to install the coil in the pod and fill the e-juice. Then, soak the coil for ten minutes. In conclusion, continuously monitor the liquid level and try to top it up when it is emptied for 70% and more.
Never leave the mod unattended during the recharging
Don't leave the device near the open fire or under the sunlight
Don't throw or shock the device
To prolong the battery lifespan, try not to drain it completely
Always charge the battery completely